Mold-Clean is a ready to use, pleasantly scented stain remover and cleaner
formulated to prepare wood and other surfaces, especially for subsequent
treatment with Bora-Care with Mold-Care.
Mold-Clean contains special wetting agents and detergents to ensure penetration deep into wood pores for thorough stain removal and effectively minimizes or eliminates scrubbing in most situations. It is not corrosive to metal fixtures and fittings.
Mold-Clean is the most powerful mold discoloration remover and surface conditioner available. In fact, Mold Clean is five times more effective than bleach alone. It’s the only product you need to truly clean a mold stained area without the intense smell of bleach cleaning products.
Key Features:
*HomeandGardenSupply.com always recommends reading the entire product label before use, and following all necessary safety precautions, mixing instructions and proper application methods.
| Active Ingredient: | Contains Water, Hypochlorous Acid (CAS#7790-92-3). |
| Product Documents: | Mold-Clean Label Mold-Clean SDS |
| Target Problem: | Mold & Mildew Stains |
| Areas Of Use: | ONLY FOR INDUSTRIAL AND PROFESSIONAL USE removes stains including algae stains from wood, brick, concrete and other surfaces. |
| Application: | COVERAGE: Approximately 150-200 square feet per gallon. Apply liberally to the point of runoff to wood or other surfaces using a low pressure (15-20 psi) sprayer. Allow surfaces to remain wet for 5-10 minutes, then thoroughly rinse with water using a high pressure stream. When using on bare wood in crawl spaces or basements, Mold-Clean can be wiped off or left to dry. If possible, apply to shaded, cool surfaces and avoid application in direct sunlight. On large jobs, clean surfaces in small sections to prevent premature drying. If application must be made in direct sunlight, lightly wet surface with water and allow to absorb prior to Mold-Clean application. Power rinsing with a commercial pressure washer may be necessary to completely remove some stains, paints or old finishes. |
| Family & Pet Safe? | If used as directed on product label |
| Formulation: | Professional |
| U.S. State Restrictions: | None |
| Dimensions: | L 6" x W 6" x H 12.5" |
| Shipping Weight: | 9.2 lbs |
| Manufacturer: | Nisus Corporation |
| EPA Registration # | N/A |
Mold-Clean is a ready to use, pleasantly scented stain remover and cleaner
formulated to prepare wood and other surfaces, especially for subsequent
treatment with Bora-Care with Mold-Care.
Mold-Clean contains special wetting agents and detergents to ensure penetration deep into wood pores for thorough stain removal and effectively minimizes or eliminates scrubbing in most situations. It is not corrosive to metal fixtures and fittings.
Mold-Clean is the most powerful mold discoloration remover and surface conditioner available. In fact, Mold Clean is five times more effective than bleach alone. It’s the only product you need to truly clean a mold stained area without the intense smell of bleach cleaning products.
Key Features:
*HomeandGardenSupply.com always recommends reading the entire product label before use, and following all necessary safety precautions, mixing instructions and proper application methods.
| Active Ingredient: | Contains Water, Hypochlorous Acid (CAS#7790-92-3). |
| Product Documents: | Mold-Clean Label Mold-Clean SDS |
| Target Problem: | Mold & Mildew Stains |
| Areas Of Use: | ONLY FOR INDUSTRIAL AND PROFESSIONAL USE removes stains including algae stains from wood, brick, concrete and other surfaces. |
| Application: | COVERAGE: Approximately 150-200 square feet per gallon. Apply liberally to the point of runoff to wood or other surfaces using a low pressure (15-20 psi) sprayer. Allow surfaces to remain wet for 5-10 minutes, then thoroughly rinse with water using a high pressure stream. When using on bare wood in crawl spaces or basements, Mold-Clean can be wiped off or left to dry. If possible, apply to shaded, cool surfaces and avoid application in direct sunlight. On large jobs, clean surfaces in small sections to prevent premature drying. If application must be made in direct sunlight, lightly wet surface with water and allow to absorb prior to Mold-Clean application. Power rinsing with a commercial pressure washer may be necessary to completely remove some stains, paints or old finishes. |
| Family & Pet Safe? | If used as directed on product label |
| Formulation: | Professional |
| U.S. State Restrictions: | None |
| Dimensions: | L 6" x W 6" x H 12.5" |
| Shipping Weight: | 9.2 lbs |
| Manufacturer: | Nisus Corporation |
| EPA Registration # | N/A |
Be the first to ask a question about this.
{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}
